|
|
@@ -41,7 +41,7 @@ This page is super not done. Just random notes for now.
|
|
|
1. Set host name: `set system host-name <host-name>`
|
|
|
1. Set domain name: `set system domain-name <domain-name>`
|
|
|
1. Set loopback addresses:
|
|
|
- 1. `set interfaces lo0.0 family inet address 127.0.0.1/8`
|
|
|
+ 1. `set interfaces lo0.0 family inet address 127.0.0.1/32`
|
|
|
1. `set interfaces lo0.0 family inet6 address ::1/128`
|
|
|
1. Set DNS: `set system name-server <addr>` (once for each address)
|
|
|
1. Set time:
|
|
|
@@ -50,15 +50,22 @@ This page is super not done. Just random notes for now.
|
|
|
1. Set server to use periodically: `set system ntp server <address>`
|
|
|
1. Set time zone: `set system time-zone Europe/Oslo` (example)
|
|
|
1. Note: After committing, use `show ntp associations` to verify NTP.
|
|
|
-1. Disable dedicated management port and alarm:
|
|
|
- 1. `set int me0 disable`
|
|
|
- 1. `set chassis alarm management-ethernet link-down ignore`
|
|
|
1. Disable default virtual chassis ports (VCPs) if not used:
|
|
|
1. Enter op mode.
|
|
|
1. Show VCPs: `show virtual-chassis vc-port`
|
|
|
1. Remove VCPs: `request virtual-chassis vc-port delete pic-slot <pic-slot> port <port-number>`
|
|
|
1. Show again to make sure they disappear. This may take a few seconds.
|
|
|
+1. Delete default interfaces configs: `wildcard range delete interface ge-0/0/[0-47]` (example, repeat for all FPSc/PICs)
|
|
|
+1. Disable unused interfaces: `wildcard range set interface ge-0/0/[0-47] disable` (example, repeat for all FPSc/PICs)
|
|
|
+1. Disable dedicated management port and alarm:
|
|
|
+ 1. Disable: `set int me0 disable`
|
|
|
+ 1. Delete logical interface: `delete int me0.0`
|
|
|
+ 1. Disable link-down alarm: `set chassis alarm management-ethernet link-down ignore`
|
|
|
+1. Disable default VLAN:
|
|
|
+ 1. Delete logical interface: `delete vlan.0` (before disabling)
|
|
|
+ 1. Disable logical interface: `set vlan.0 disable`
|
|
|
1. Setup port-ranges: **TODO**
|
|
|
+1. Setup VLANs (not interfaces): `set vlans <name> vlan-id <VID>`
|
|
|
1. Setup LACP:
|
|
|
1. Set number of available LACP interfaces: `set chassis aggregated-devices ethernet device-count <0-64>`
|
|
|
1. Add individual Ethernet interfaces (not using interface range):
|
|
|
@@ -69,8 +76,7 @@ This page is super not done. Just random notes for now.
|
|
|
1. Set LACP options: `set aggregated-ether-options lacp active [periodic fast]`
|
|
|
1. Setup default logical unit: `edit unit 0`
|
|
|
1. Setup VLAN/address/etc.
|
|
|
-1. Setup VLANs:
|
|
|
- 1. Create named VLANs: `set vlans <name> vlan-id <VID>`
|
|
|
+1. Setup VLAN interfaces:
|
|
|
1. Setup trunk ports:
|
|
|
1. Enter unit 0 and `family ethernet-switching` of the physical/LACP interface.
|
|
|
1. Set mode: `set port-mode trunk`
|
|
|
@@ -80,11 +86,15 @@ This page is super not done. Just random notes for now.
|
|
|
1. Enter unit 0 and `family ethernet-switching` of the physical/LACP interface.
|
|
|
1. Set access VLAN: `set vlan members <VLAN-name>`
|
|
|
1. Setup L3 interfaces:
|
|
|
+ 1. (VLAN) Set L3-interface: `set vlans <name> l3-interface vlan.<VID>`
|
|
|
1. Enter unit 0 of physical/LACP interface or `vlan.<VID>` for VLAN interfaces.
|
|
|
1. Set IPv4 address: `set family inet address <address>/<prefix-length>`
|
|
|
1. Set IPv6 address: `set family inet6 address <address>/<prefix-length>`
|
|
|
- 1. (VLAN) Set L3-interface: `set vlans <name> l3-interface vlan.<VID>`
|
|
|
+1. Setup static IP routes:
|
|
|
+ 1. IPv4 default gateway: `set routing-options rib inet.0 static route 0.0.0.0/0 next-hop <next-hop>`
|
|
|
+ 1. IPv6 default gateway: ``set routing-options rib inet6.0 static route ::0/0 next-hop <next-hop>``
|
|
|
1. Configure RSTP: **TODO**
|
|
|
+1. Configure SNMP (public RO): `set snmp community public authorization read-only`
|
|
|
1. Enable auto snapshotting and restoration on corruption: `set system auto-snapshot`
|
|
|
1. Disable DHCP auto image upgrade: `delete chassis auto-image-upgrade`
|
|
|
1. Commit configuration: `commit [confirmed]`
|
|
|
@@ -159,7 +169,7 @@ Virtual Chassis Fabric (VCF) evolves VC into a spine-and-leaf architecture. Whil
|
|
|
- (Optional) Create range or do it per phys. int.
|
|
|
- `set interfaces ge-0/0/0 ether-options 802.3ad ae0`
|
|
|
- `set interfaces ae0 aggregated-ether-options lacp active`
|
|
|
- - `set aggregated-devices ethernet device-count <n>` (0-127)
|
|
|
+ - `set aggregated-devices ethernet device-count <n>` (0-64)
|
|
|
- Set IP address: `set interfaces ae0 unit 0 family inet address 10.0.0.1/30`
|
|
|
- Static route: `set routing-options static route 10.0.0.0/24 next-hop 10.0.1.1`
|
|
|
- `show configuration [...] | display set`
|
Håvard O. Nordstrand